📱 Call Us

FSD25 WINNER: Emerson Garcia, Gonzales, LA. BMT #3 WINNER: Eric Dassinger, Wichita Falls, TX.
1 7
Mishimoto

Mishimoto 15+ Ford Mustang EcoBoost 2.3L / 12-18 Ford Focus ST Ignition Coil Single

SKU: MISMMIG-FOST-12
$77.99

Not sure which part you need, or want to make sure it's in stock?

Give us a call. You won't get a robot, you'll get straight through to a real person who knows diesel.

📱 Call Us

The basic requirements for a properly running engine are fuel, air, compression, and spark. Before cranking up the boost in your EcoBoost, it is wise to ensure all maintenance is up to date and these processes are performing as intended. Weak spark from your ignition system can result in misfiring under high load driving, and spark blow-out under high boost, which is bad for performance. Mishimoto is proud to launch our new lineup of ignition coils, aimed at providing a high-quality replacement that can bring your vehicle up to Stage 0 before moving on to horsepower adding modifications. Our ignition coils are designed and tested to meet or exceed OEM Ford performance standards and are available as a single coil or in sets of four. Once installed with a set of new spark plugs, one can expect a refreshed ignition system with improved engine startup, a smoother idle, and restored performance from your EcoBoost. The primary frame of our coils is constructed from extremely robust phenolic resin, ensuring optimal longevity in high temperature environments. The precision lower boot provides a barrier against moisture entry into the plug well, eliminating chances for spark plug contamination. In addition, our coils are pre-lubricated with dielectric grease to prevent corrosion and ensure an optimal connection between the spark plug and coil. Mishimoto ignition coils are an ideal replacement for worn or defective factory coils. As with all our products, these ignition coils include our signature Mishimoto Lifetime Warranty.

  • Designed and tested to meet or exceed OEM Ford performance specifications
  • Improves engine startup, idle, and restores your Ecoboost's performance
  • High-quality replacement coils available in full sets or single units

This Part Fits:

Year Make Model Submodel
2018-2021 Ford EcoSport S
2018-2021 Ford EcoSport SE
2018-2021 Ford EcoSport SES
2018-2021 Ford EcoSport Titanium
2012-2014 Ford Edge Limited
2012-2018 Ford Edge SE
2012-2018 Ford Edge SEL
2015-2018 Ford Edge Titanium
2013-2019 Ford Escape SE
2013,2018-2019 Ford Escape SEL
2013-2019 Ford Escape Titanium
2012-2019 Ford Explorer Base
2012-2019 Ford Explorer Limited
2012-2019 Ford Explorer XLT
2016-2018 Ford Focus RS
2013-2017 Ford Focus S
2012-2017 Ford Focus SE
2017 Ford Focus SEL
2013-2018 Ford Focus ST
2013-2017 Ford Focus Titanium
2017-2018 Ford Fusion Platinum
2017-2018 Ford Fusion Platinum Hybrid
2014-2018 Ford Fusion S Hybrid
2013-2020 Ford Fusion SE
2013-2020 Ford Fusion SE Hybrid
2019 Ford Fusion SEL
2019-2020 Ford Fusion SEL Hybrid
2013-2020 Ford Fusion Titanium
2013-2020 Ford Fusion Titanium Hybrid
2015-2020 Ford Mustang EcoBoost
2015-2020 Ford Mustang EcoBoost Premium
2013-2017 Ford Taurus Limited
2013-2017 Ford Taurus SE
2013-2017 Ford Taurus SEL
2015,2019 Lincoln MKC Base
2015-2019 Lincoln MKC Black Label
2016-2018 Lincoln MKC Premiere
2016-2019 Lincoln MKC Reserve
2016-2019 Lincoln MKC Select
2013-2016 Lincoln MKT Base
2013-2016,2019-2020 Lincoln MKZ Base
2015-2018 Lincoln MKZ Black Label
2015-2018 Lincoln MKZ Black Label Hybrid
2013-2016,2019 Lincoln MKZ Hybrid
2017-2018 Lincoln MKZ Premiere
2017-2018 Lincoln MKZ Premiere Hybrid
2017-2018,2020 Lincoln MKZ Reserve
2017-2018,2020 Lincoln MKZ Reserve Hybrid
2019 Lincoln MKZ Reserve I
2019 Lincoln MKZ Reserve I Hybrid
2019 Lincoln MKZ Reserve II
2019 Lincoln MKZ Reserve II Hybrid
2017-2018 Lincoln MKZ Select

Customer Reviews

Overall rating: 4.7 / 5 from 529 reviews.

Customer photo review of FSD 03-09 Dodge Cummins Billet Heat Exchanger

The billet heat exchanger looks great and is machined nicely. No worries about an internal failure allowing fluids to mix. It seems to be doing its job. It's more robust than the factory style cooler but I don’t believe it is quite as efficient based on warm up times I’m seeing. My only gripe is the bracket mounting bolts, they thread directly onto the cooler instead of passing all the way through and securing with nuts. Make sure to use thread locker along with the lock washers. As a rough guide, torque for M8 fasteners in aluminum should be 11-15 ft lbs, no torque spec is listed for the mounting hardware in the instructions.

Charles H. 4/5 Verified

FSD 03-09 Dodge Cummins Billet Heat Exchanger

Customer photo review of FSD 2003-2007 Dodge Cummins Heater Hose Kit Black Braided

It’s not bad, I was in a bind and needed a quick fix to get my truck back going. So first things first, the kit works. You can get rid of the steel lines and these will take their place. With about an hour and a half and a little research it doesn’t take much to get these hoses installed. However, I have some gripes about this kit. 1. You have to be very careful about how the lines are run to prevent the hose from kinking. 2. There are no p clamps or hardware included to hold the lines in place. To improve this kit, I’d toss some hose clamps, a couple bolts with some p clamps to hold the hose, maybe a couple pictures on where to run things too, or even total install instructions. Stiffer hose would be good too, in my pictures you can see that the hose going to the front of the engine is trying to kink as it makes the bend to run beside the turbo.

Noah T. 3/5 Verified

FSD 2003-2007 Dodge Cummins Heater Hose Kit Black Braided

Customer photo review of Kingspeed Billet Front Cover 94-02

It came with no gaskets this item deff needs to be sold with cover gasket as well as the seal for the crank even a plug for the vent or a fitting to hook a tube to the vent. Didn’t come with shit but bolts. Now I got to track everything else down seperatly makes it a pain in the ass. At this point I’d rather have stayed stock

Jacob M. 3/5 Verified

Kingspeed Billet Front Cover 94-02

Customer photo review of FSD 2010-2012 Dodge Cummins Factory Replacement Transmission Line Kit Black Braided

I installed them when I built my transmission. Hoses are good quality but fittings felt kind of cheap. Not a bad kit at all. I’d recommend it to anyone. Substantial trans temp difference after putting them on. My trans runs a lot cooler now that I’ve bypassed the heat exchanger. 2012 ram 2500 with 68rfe. 9/10 would recommend. Just be gentle with the fittings

Max F. 4/5 Verified

FSD 2010-2012 Dodge Cummins Factory Replacement Transmission Line Kit Black Braided

Customer photo review of FSD 03-09 Dodge Cummins Elite Drop-In Transmission Cooler Kit

I installed this cooler and a few weeks later got into a wreck that was able to damn near total my truck, the frame is bent in 4 places and it shifted my ranch and bumper a foot. This cooler was the only radiator that survived everything else was destroyed and wrapped around the cooler. I called customer support and was able to order new stainless steel brackets and this cooler will live again. I’m very impressed with the quality and strength of this part and would gladly buy it for another truck.

Fritz G. 5/5

FSD 03-09 Dodge Cummins Elite Drop-In Transmission Cooler Kit

Customer photo review of Kingspeed 06-Current Dodge Ram Billet Budget Builder Valve Cover

I love the product. I am just upset that it wasn’t clear it doesn’t come with any hardware. I currently have no clue what barb fittings and hose sizes I need to get for the valve cover to my catch can. I am currently using a hardware store setup as this is my first Cummins and my first quality build of a truck. If there’s anyway you could assist me or point me in the right direction that would be awesome. Aside from that I’ve had nothing but compliments on it, I actually won top 10 truck and SCT x GFP in Nashville a few weeks back. Everyone including myself love the valve cover.

Caleb H. 3/5 Verified

Kingspeed 06-Current Dodge Ram Billet Budget Builder Valve Cover

⌕