📱 Call Us

FSD25 WINNER: Emerson Garcia, Gonzales, LA. BMT #3 WINNER: Eric Dassinger, Wichita Falls, TX.
ORACLE Lighting

Oracle Trigger 6 Shooter Wireless Accessory Control System

SKU: ORL3001
$405.99
  • Make: Universal

Not sure which part you need, or want to make sure it's in stock?

Give us a call. You won't get a robot, you'll get straight through to a real person who knows diesel.

📱 Call Us

The Trigger 6 SHOOTER Wireless Accessory Control System substantially saves your electronic accessories' installation time! Eliminate the need to run wires under the dash or through the firewall of a vehicle when wiring accessories. It also adds functionality such as an RF remote control for activating installed accessories from outside the vehicle and dimming/flashing functions for installed lighting. In addition, fused circuits with LED indicators notify you of blown fuses. The included battery-powered RF remote utilizes a universal mounting system that will accommodate round surfaces as well as flat surfaces. Its buttons are back-lit and it is programmable for security or use with additional remotes. Several Trigger control boxes and remotes can be used together to control up to 24 accessories. When mounted to a UTV roll bar, the buttons on the remote are more easily accessible than dash switches. No straining against seat belts to reach the dash, just a quick reach up to tap the remote. The Bluetooth App will control on/off and dimming functions as well as flashing when used with LED or conventional lighting. It is simple to set up and allows for user customization. Use the app to "Trigger" lights from outside the vehicle whenever you might need to activate an accessory on demand.

Installation Instructions
Installation Instructions
  • Built-in Bluetooth battery monitor - see connected battery voltage in real-time on the TRIGGER ACS PLUS app
  • Backlit switches when optionally connected to 12 Volt power via an 8' long, thin 28 gauge harness
  • You can control it from your mobile device with our free TRIGGER ACS PLUS App for iOS/Android!
  • Built in DIN connector for use of conventional toggle switches (harness sold separately)
  • High intensity LED's indicate circuit status, blue for circuit on, red for blown f
  • Low voltage cut off will shut down the 6 Shooter if battery voltage gets too low
  • Waterproof case design, withstands temps from below freezing to 250 degrees F
  • Built in fuses with o-ring sealed cover: two 30 amp, two 10 amp, two 5 amp
  • RF Remote with rocker-style switches usable inside or outside the vehicle
  • 100 amp fuse installed on positive input wire for whole system protection
  • 12 to 24 volt input, 3 wires, ground, switched positive, battery positive
  • Six 12-24 volt output harnesses with pre-installed waterproof connectors
  • Includes six 8-foot-long wire harnesses with waterproof connectors
  • Manual buttons for individual circuit power on top of control box
  • Free 3-year warranty that covers manufacturing defects
  • Wireless back-lit RF remote rocker switch module
  • Two 30, two 10, and two 5 amp fused circuits
  • Set custom backlight colors on the remote!
  • Comes with switch labels too!
  • Accepts 12-24 Volt input

Customer Reviews

Overall rating: 4.7 / 5 from 529 reviews.

Customer photo review of FSD 03-09 Dodge Cummins Billet Heat Exchanger

The billet heat exchanger looks great and is machined nicely. No worries about an internal failure allowing fluids to mix. It seems to be doing its job. It's more robust than the factory style cooler but I don’t believe it is quite as efficient based on warm up times I’m seeing. My only gripe is the bracket mounting bolts, they thread directly onto the cooler instead of passing all the way through and securing with nuts. Make sure to use thread locker along with the lock washers. As a rough guide, torque for M8 fasteners in aluminum should be 11-15 ft lbs, no torque spec is listed for the mounting hardware in the instructions.

Charles H. 4/5 Verified

FSD 03-09 Dodge Cummins Billet Heat Exchanger

Customer photo review of FSD 2003-2007 Dodge Cummins Heater Hose Kit Black Braided

It’s not bad, I was in a bind and needed a quick fix to get my truck back going. So first things first, the kit works. You can get rid of the steel lines and these will take their place. With about an hour and a half and a little research it doesn’t take much to get these hoses installed. However, I have some gripes about this kit. 1. You have to be very careful about how the lines are run to prevent the hose from kinking. 2. There are no p clamps or hardware included to hold the lines in place. To improve this kit, I’d toss some hose clamps, a couple bolts with some p clamps to hold the hose, maybe a couple pictures on where to run things too, or even total install instructions. Stiffer hose would be good too, in my pictures you can see that the hose going to the front of the engine is trying to kink as it makes the bend to run beside the turbo.

Noah T. 3/5 Verified

FSD 2003-2007 Dodge Cummins Heater Hose Kit Black Braided

Customer photo review of Kingspeed Billet Front Cover 94-02

It came with no gaskets this item deff needs to be sold with cover gasket as well as the seal for the crank even a plug for the vent or a fitting to hook a tube to the vent. Didn’t come with shit but bolts. Now I got to track everything else down seperatly makes it a pain in the ass. At this point I’d rather have stayed stock

Jacob M. 3/5 Verified

Kingspeed Billet Front Cover 94-02

Customer photo review of FSD 2010-2012 Dodge Cummins Factory Replacement Transmission Line Kit Black Braided

I installed them when I built my transmission. Hoses are good quality but fittings felt kind of cheap. Not a bad kit at all. I’d recommend it to anyone. Substantial trans temp difference after putting them on. My trans runs a lot cooler now that I’ve bypassed the heat exchanger. 2012 ram 2500 with 68rfe. 9/10 would recommend. Just be gentle with the fittings

Max F. 4/5 Verified

FSD 2010-2012 Dodge Cummins Factory Replacement Transmission Line Kit Black Braided

Customer photo review of FSD 03-09 Dodge Cummins Elite Drop-In Transmission Cooler Kit

I installed this cooler and a few weeks later got into a wreck that was able to damn near total my truck, the frame is bent in 4 places and it shifted my ranch and bumper a foot. This cooler was the only radiator that survived everything else was destroyed and wrapped around the cooler. I called customer support and was able to order new stainless steel brackets and this cooler will live again. I’m very impressed with the quality and strength of this part and would gladly buy it for another truck.

Fritz G. 5/5

FSD 03-09 Dodge Cummins Elite Drop-In Transmission Cooler Kit

Customer photo review of Kingspeed 06-Current Dodge Ram Billet Budget Builder Valve Cover

I love the product. I am just upset that it wasn’t clear it doesn’t come with any hardware. I currently have no clue what barb fittings and hose sizes I need to get for the valve cover to my catch can. I am currently using a hardware store setup as this is my first Cummins and my first quality build of a truck. If there’s anyway you could assist me or point me in the right direction that would be awesome. Aside from that I’ve had nothing but compliments on it, I actually won top 10 truck and SCT x GFP in Nashville a few weeks back. Everyone including myself love the valve cover.

Caleb H. 3/5 Verified

Kingspeed 06-Current Dodge Ram Billet Budget Builder Valve Cover

⌕