📱 Call Us

FSD26 IS LIVE: Every $1 spent = 150 entries to win a 2024 F-350 Limited + $20,000 cash.
1 9
AWE Tuning

AWE Tuning BMW F8X M3/M4 SwitchPath Cat-Back Exhaust - Diamond Black Tips

SKU: AWE3025-43074
$2,891.99
  • Make: BMW
  • Year/Engine: 2015-2020 F8X M3/M4

Not sure which part you need, or want to make sure it's in stock?

Give us a call. You won't get a robot, you'll get straight through to a real person who knows diesel.

📱 Call Us
433650 Entries150X
This purchase enters you to win the FSD26 truck: a 2024 F-350 Limited + $20,000 cash. Ends October 18. See the truck

We made the S55 sound epic with the valves closed, and with them open… again! All while remaining emissions compliant. Presenting the second generation of SwitchPath™ Exhaust for the BMW F8X M3 and M4. Minimal bends, maximum flow, and push-button attitude. The SwitchPath™ Exhaust is a true Cat Back configuration comprised of 3-inch and 2.5-inch U.S.-sourced T304L stainless steel, a precision x-pipe, and a valved SwitchPath™ muffler tuned specifically for the S55. Beginning after the secondary catalysts, the precision X-pipe immediately helps smooth the S55 of its infamous rasp, allowing the tone to be further refined by the bespoke muffler in the rear. When the valves are closed, the SwitchPath™ Exhaust produces a refined, aggressive howl while remaining full-bodied and powerful – no congested, metallic sounds here when on the throttle. At cruising speeds, interior acoustics are close to stock. AWE SwitchPath™ tech also responds perfectly to the many transmission settings and shift points in DCT vehicles. Drop the hammer with the valves closed and SwitchPath™ sings a proper M anthem. If you were to leave the valves closed at all times after equipping SwitchPath™, we wouldn’t blame you — it’s that good… all the time. Open the valves and the S55’s roar is uncorked. Sport and Sport+ modes achieve the ultimate contrast in behavior when compared to comfort driving modes (valves closed). In Sport mode, the exhaust note is powerful, clean, and aggressive. In Sport+ mode, the same aggression applies… but with grin-provoking burbles…a lot of grin-provoking burbles. Thanks to the precision X-pipe, the rasp is still kept in check while allowing the exhaust note to reach full aggression. If you’re looking for the best of both worlds and want to retain your factory valve behavior all while gaining peace of mind (i.e. emissions compliance), look no further than SwitchPath™. Comes complete with quad diamond black tips, and AWE's No CEL Guarantee.

  • SwitchPath™ utilizes factory valving and retains M-Sport button functionality
  • Tip options include 102mm double-walled, slash-cut tips in Diamond Black
  • 50-state legal Cat Back design: sick sound with all catalysts intact
  • Proudly engineered, designed, and manufactured in-house at AWE
  • Handcrafted from U.S.-sourced .065" wall T304L stainless steel
  • Max gains of 12 hp and 16 lb-ft of torque at the wheels
  • Precision-engineered X-pipe to unlock a clean S55 tone
  • Unified design for OPF euro and non-euro spec cars
  • 3” CNC mandrel-bent Cat Back configuration
  • Featuring the AWE Lifetime Exhaust Warranty
  • No Check Engine Light Guarantee
  • Perfect Fitment Guarantee

This Part Fits:

Year Make Model Submodel
2015-2018 BMW M3 Base
2015-2020 BMW M4 Base
2019-2020 BMW M4 CS
2016 BMW M4 GTS

Customer Reviews

Overall rating: 4.7 / 5 from 531 reviews.

Customer photo review of FSD 03-09 Dodge Cummins Billet Heat Exchanger

The billet heat exchanger looks great and is machined nicely. No worries about an internal failure allowing fluids to mix. It seems to be doing its job. It's more robust than the factory style cooler but I don’t believe it is quite as efficient based on warm up times I’m seeing. My only gripe is the bracket mounting bolts, they thread directly onto the cooler instead of passing all the way through and securing with nuts. Make sure to use thread locker along with the lock washers. As a rough guide, torque for M8 fasteners in aluminum should be 11-15 ft lbs, no torque spec is listed for the mounting hardware in the instructions.

Charles H. 4/5 Verified

FSD 03-09 Dodge Cummins Billet Heat Exchanger

Customer photo review of FSD 2003-2007 Dodge Cummins Heater Hose Kit Black Braided

It’s not bad, I was in a bind and needed a quick fix to get my truck back going. So first things first, the kit works. You can get rid of the steel lines and these will take their place. With about an hour and a half and a little research it doesn’t take much to get these hoses installed. However, I have some gripes about this kit. 1. You have to be very careful about how the lines are run to prevent the hose from kinking. 2. There are no p clamps or hardware included to hold the lines in place. To improve this kit, I’d toss some hose clamps, a couple bolts with some p clamps to hold the hose, maybe a couple pictures on where to run things too, or even total install instructions. Stiffer hose would be good too, in my pictures you can see that the hose going to the front of the engine is trying to kink as it makes the bend to run beside the turbo.

Noah T. 3/5 Verified

FSD 2003-2007 Dodge Cummins Heater Hose Kit Black Braided

Customer photo review of Kingspeed Billet Front Cover 94-02

It came with no gaskets this item deff needs to be sold with cover gasket as well as the seal for the crank even a plug for the vent or a fitting to hook a tube to the vent. Didn’t come with shit but bolts. Now I got to track everything else down seperatly makes it a pain in the ass. At this point I’d rather have stayed stock

Jacob M. 3/5 Verified

Kingspeed Billet Front Cover 94-02

Customer photo review of FSD 2010-2012 Dodge Cummins Factory Replacement Transmission Line Kit Black Braided

I installed them when I built my transmission. Hoses are good quality but fittings felt kind of cheap. Not a bad kit at all. I’d recommend it to anyone. Substantial trans temp difference after putting them on. My trans runs a lot cooler now that I’ve bypassed the heat exchanger. 2012 ram 2500 with 68rfe. 9/10 would recommend. Just be gentle with the fittings

Max F. 4/5 Verified

FSD 2010-2012 Dodge Cummins Factory Replacement Transmission Line Kit Black Braided

Customer photo review of FSD 03-09 Dodge Cummins Elite Drop-In Transmission Cooler Kit

I installed this cooler and a few weeks later got into a wreck that was able to damn near total my truck, the frame is bent in 4 places and it shifted my ranch and bumper a foot. This cooler was the only radiator that survived everything else was destroyed and wrapped around the cooler. I called customer support and was able to order new stainless steel brackets and this cooler will live again. I’m very impressed with the quality and strength of this part and would gladly buy it for another truck.

Fritz G. 5/5

FSD 03-09 Dodge Cummins Elite Drop-In Transmission Cooler Kit

Customer photo review of Kingspeed 06-Current Dodge Ram Billet Budget Builder Valve Cover

I love the product. I am just upset that it wasn’t clear it doesn’t come with any hardware. I currently have no clue what barb fittings and hose sizes I need to get for the valve cover to my catch can. I am currently using a hardware store setup as this is my first Cummins and my first quality build of a truck. If there’s anyway you could assist me or point me in the right direction that would be awesome. Aside from that I’ve had nothing but compliments on it, I actually won top 10 truck and SCT x GFP in Nashville a few weeks back. Everyone including myself love the valve cover.

Caleb H. 3/5 Verified

Kingspeed 06-Current Dodge Ram Billet Budget Builder Valve Cover

⌕